Step Instruction for Bathtub Installation
Step Instruction for Bathtub Installation
Blog Article
Are you currently interested in information around How to Install a Bathtub Yourself?
Installing a bath tub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably hard project. If the old bathtub is readily obtainable, the task can move quickly; if you have to open up a wall to eliminate the old tub and also position the new bath tub, the task is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed project, it is better to think about using one before you start. Chances are you may require an expert plumber to make tube links.
This post will assist you mount a new bath tub in your restroom if you have actually already bought a new tub as well as do not need to change the setup of your previous supply of water pipelines.
Your devices and product checklist should comprise the following:
Planning for the Installment
To start with, the supporting framework provided with the bathroom must be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to prevent strain on the bath tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is detach the water. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning during this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before going on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Making use of the two wood boards under its feet, place the bath tub in the called for position. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub up until the spirit level reviews level.
To install taps, fit the bottom of the outermost adaptable faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Switch on the supply of water and inspect all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub as well as likewise check the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub ought to wait till the bathtub has actually been used at the very least when as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin ensuring that the washing machines are in area between the tap as well as the sink. Protect the tap in place with the maker given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type must be attached to the faucet ends initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a stiff seal, triggering the water to penetrate the wall in between the bath and the tiling, causing difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealant can crack relatively very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I was shown that article about How to Install a Bathtub through a good friend on a different blog. Appreciated our piece? Please share it. Let others check it out. We thank you for reading our article about How to Install a Bathtub.
Certified emergency plumbing assistance available. Report this page